HomeStore

NOPRO | Short Stabilizer Link Set for Mazda Miata MX5 NC

NOPRO | Short Stabilizer Link Set for Mazda Miata MX5 NC

NOPRO | Short Stabilizer Link Set for Mazda Miata MX5 NC

Short stabilizer link set for NC
 

This is a short type stabilizer link with the same shape as the factory stabilizer link, which allows you to set the relative angle between the stabilizer (anti-roll bar) and lower arm to a more appropriate state than the factory stabilizer link when lowering and tuning your car.
By setting the stabilizer at the ideal expected angle, unnecessary tension during cornering is eliminated, allowing for stable driving.
 
Front:

50mm shorter than OEM. For vehicles with
a ride height lowered by 25-55mm
. Will not fit properly on any other vehicle.
 

Rear:

25mm shorter than OEM. For vehicles with
a ride height lowered by 10-45mm
. Will not fit properly on any other vehicle.

 

Please be sure to fully understand the function of the stabilizer before using it.
If used in an incompatible condition, the link may break.
It can be replaced with a bolt-on.

 

 

 
 

★ Caution ★
 
If the vehicle height is lowered only with low-down springs, the damper shaft may extend more than expected at zero G, which may put strain on the front stabilizer link in particular. Please adjust the extension stroke to the appropriate value by installing a stroke-up upper mount, etc.

 

If your rear shock absorber has a long extension stroke, it is possible that the stabilizer itself may point downwards when lifted, causing it to move in a direction outside of its normal operating range. Lower the lift and check before 1G is applied. If it is in the normal operating position, there is no problem.

 

If your vehicle is equipped with a product that allows you to adjust the hardness of the front stabilizer by adjusting the hole position, and the front stabilizer link is too short to reach the hole, you may be able to solve the problem by swapping the left and right links and installing them.

 

It is possible to use it with the RX8 if the conditions of use are met, but please use it at your own risk, taking into consideration the operating range of the link mechanism and the damper stroke.

 

Due to differences in the shape of the stabilizer used, if it is used beyond the operating range even though it is physically impossible to install, the ball joint may be damaged.　

 

Before using the product, please make sure that the link mechanism operates properly and securely when the vehicle is under 1G.
 

*PLEASE NOTE*

This is a Japan Parts Service, some items are made to order (typically 4-8 weeks to make)

If you select air mail expect a 4-6 week wait (could be less if in stock in Japan)

If you select container service expect 4-6 month wait

All sales are final, please expect delays and do not purchase from this section if you're in a hurry!


$115.50

Original: $330.00

-65%
NOPRO | Short Stabilizer Link Set for Mazda Miata MX5 NC—

$330.00

$115.50
Product image 1
Product image 2
Product image 3

Description

NOPRO | Short Stabilizer Link Set for Mazda Miata MX5 NC

Short stabilizer link set for NC
 

This is a short type stabilizer link with the same shape as the factory stabilizer link, which allows you to set the relative angle between the stabilizer (anti-roll bar) and lower arm to a more appropriate state than the factory stabilizer link when lowering and tuning your car.
By setting the stabilizer at the ideal expected angle, unnecessary tension during cornering is eliminated, allowing for stable driving.
 
Front:

50mm shorter than OEM. For vehicles with
a ride height lowered by 25-55mm
. Will not fit properly on any other vehicle.
 

Rear:

25mm shorter than OEM. For vehicles with
a ride height lowered by 10-45mm
. Will not fit properly on any other vehicle.

 

Please be sure to fully understand the function of the stabilizer before using it.
If used in an incompatible condition, the link may break.
It can be replaced with a bolt-on.

 

 

 
 

★ Caution ★
 
If the vehicle height is lowered only with low-down springs, the damper shaft may extend more than expected at zero G, which may put strain on the front stabilizer link in particular. Please adjust the extension stroke to the appropriate value by installing a stroke-up upper mount, etc.

 

If your rear shock absorber has a long extension stroke, it is possible that the stabilizer itself may point downwards when lifted, causing it to move in a direction outside of its normal operating range. Lower the lift and check before 1G is applied. If it is in the normal operating position, there is no problem.

 

If your vehicle is equipped with a product that allows you to adjust the hardness of the front stabilizer by adjusting the hole position, and the front stabilizer link is too short to reach the hole, you may be able to solve the problem by swapping the left and right links and installing them.

 

It is possible to use it with the RX8 if the conditions of use are met, but please use it at your own risk, taking into consideration the operating range of the link mechanism and the damper stroke.

 

Due to differences in the shape of the stabilizer used, if it is used beyond the operating range even though it is physically impossible to install, the ball joint may be damaged.　

 

Before using the product, please make sure that the link mechanism operates properly and securely when the vehicle is under 1G.
 

*PLEASE NOTE*

This is a Japan Parts Service, some items are made to order (typically 4-8 weeks to make)

If you select air mail expect a 4-6 week wait (could be less if in stock in Japan)

If you select container service expect 4-6 month wait

All sales are final, please expect delays and do not purchase from this section if you're in a hurry!


NOPRO | Short Stabilizer Link Set for Mazda Miata MX5 NC | Parts From Japan